IS215VCMIH2B | Mark VIe Power Supply Module | New Surplus

Description

Product Introduction

The GE IS215VCMIH2B is a VMEbus primary power supply module from the Mark VIe Speedtronic series, purpose-built to provide regulated DC power to the Mark VIe control system backplanes. This board converts the plant’s nominal 125 VDC bus (typically from battery-backed DC supplies) into the clean, regulated voltages required by processor boards, I/O modules, communication interfaces, and field devices. The H2B revision features higher current capacity, enhanced diagnostics, and improved efficiency compared to earlier variants.

What sets the VCMIH2B revision apart is its robust input filtering, wide input voltage tolerance (100–150 VDC), efficient operation (92% typical), enhanced diagnostics including voltage monitoring, current monitoring, temperature sensing, and predictive health monitoring. The board delivers 5 VDC at up to 30 A for logic circuits, ±12 VDC at 4 A for auxiliary circuits, and 24 VDC at 5 A for field I/O—all with low ripple for stable operation. Advanced features include input transient protection, output overvoltage and overcurrent protection, and comprehensive status monitoring. For system integrators requiring high-capacity, high-performance primary power with advanced diagnostics for heavily loaded Mark VIe systems, this board is the direct OEM solution.

Key Technical Specifications

Key Selling Points & Differentiators

• High Current Capacity: 30 A on 5 V rail—supports the most heavily loaded backplanes.
• Higher Efficiency: 92% efficiency—reduces heat generation and improves reliability.
• Multiple Output Rails: 5 V, ±12 V, and 24 V outputs—supplies all backplane power requirements.
• Enhanced Transient Protection: 2,000 V surge withstand—superior protection from plant electrical disturbances.
• Enhanced Diagnostics: Voltage, current, temperature, and health monitoring with predictive indicators.
• Predictive Health Monitoring: Capacitor aging estimation enables proactive maintenance planning.
• Comprehensive Protection: Foldback current limiting, overvoltage clamping, and thermal shutdown.
• Live Test Verified: Every board undergoes a 48-hour burn-in at full rated load with cycling input voltage. We log output voltages, ripple, thermal performance, and diagnostic thresholds.
• 90-Day Warranty: Covers functional defects. If it fails under normal operating conditions, we replace it. No restocking fee for verified returns.
• OEM Traceability: All units come from audited surplus channels with original GE anti-static bags and serialized labels.
• Pre-Shipment Capacitor Reform: For units stored more than 12 months, we perform controlled capacitor reforming to prevent inrush failures.

Frequently Asked Questions (FAQ)

Q: What is the difference between IS215VCMIH2B and IS215VCMIH1B?

A: The H2B has significant improvements: higher 5 V current (30 A vs. 25 A), higher auxiliary currents (4 A vs. 3 A, 5 A vs. 4 A), higher efficiency (92% vs. 91%), lower ripple (<25 mV vs. <30 mV), and enhanced transient protection (2,000 V vs. 1,500 V). The H2B also requires Mark VIe Toolkit v6.5 or higher. If you need higher capacity and enhanced protection, choose H2B.

Q: What is the difference between IS215VCMIH2B and IS215VCMIH2A?

A: The H2B revision typically includes enhanced diagnostics or minor performance improvements over H2A. Check your existing board—if you have H2A, verify compatibility. In most cases, H2A and H2B are interchangeable, but confirm with the board’s firmware requirements.

Q: What is the predictive health monitoring feature?

A: The VCMIH2B continuously monitors capacitor aging and estimates remaining capacitor life based on temperature and operating hours. This enables proactive maintenance planning—you can replace the power supply during scheduled maintenance rather than reacting to unexpected failure.

Q: What is the benefit of the 92% efficiency?

A: At 92% efficiency, the VCMIH2B generates less heat than lower efficiency supplies. For a 562 W power supply, 92% efficiency generates approximately 45 W of heat vs. 50 W at 91%. This difference is significant in tightly packed cabinets and can extend component life.

Q: What is the benefit of the 2,000 V transient protection?

A: The 2,000 V surge withstand provides superior protection from voltage spikes caused by lightning strikes, switching transients, or other plant electrical disturbances. This is a significant advantage over basic power supplies that lack transient protection or have lower ratings.

Q: Can I use this board with 24 VDC or 48 VDC input instead of 125 VDC?

A: No. The VCMIH2B is specifically designed for 125 VDC nominal input (100–150 VDC range). Using lower or higher voltages will damage the board or fail to regulate properly.

Q: Is this board hot-swappable?

A: No. The Mark VIe VME backplane does not support live insertion of power boards. You must de-energize the rack and discharge capacitors before removal.

Q: What is the typical lead time for this part?

A: We stock these on the shelf—usually ship within 24 hours. For international orders, add 3–5 days for customs.

Q: Does this board work with both Mark VIe and Mark VIeS (SIL-rated) cabinets?

A: Yes—with a caveat. SIL systems typically require redundant power supplies. The H2B can be used in those configurations, but ensure your backplane supports OR-ing diodes. We can help verify compatibility.

Q: What’s your return policy if this doesn’t fix my power-related fault?

A: If the board passes our QC test but doesn’t clear your fault, accept a return within 30 days provided no physical damage or overvoltage stress. We charge a 15% restocking fee if the fault was due to downstream short circuits or incorrect input voltage. We’ll diagnose with you before shipping.

IS200 VSVOH MARK VI CARD
IS200 VSVOH1B MARK VI CARD
IS200 VSVOH1BED VME SERVO CARD
IS200 VTCC THERMOCOUPLE