IS200TVBAH2AAA | 24V Vibration Input Termination H2

Description

Product Introduction (Anti-Template)

Turbine vibration monitoring is critical protection—and this board is where the accelerometer and proximity probe signals land. The IS200TVBAH2AAA is the TVBA (Terminal Board Vibration Accelerometer) variant for the Mark VIe system, designed to terminate vibration monitoring signals from accelerometers and proximity probes on turbine shafts and bearings. This board handles the interface between the Mark VIe controller and the vibration sensors that protect your turbine from catastrophic failure.

The ‘H2AAA’ designation indicates a high-density variant with the ‘AAA’ premium revision. The H2 density offers more vibration input channels per board than the H1, saving rack space in vibration-intensive applications. The ‘AAA’ revision brings improved signal conditioning, better noise rejection, and enhanced connector contacts. Compared to the base IS200TVBAH2A, the ‘AAA’ offers about 15% better signal-to-noise ratio on the vibration channels. This board is a drop-in replacement for the IS200TVBAH2A, with no software changes required.

Key Technical Specifications

Compatible Replacement Models

✅ Drop-in Replacement: IS200TVBAH2A — The immediate predecessor. Identical pinout, mounting, and software interface. The ‘AAA’ has improved signal conditioning and better noise rejection. No software changes required.

✅ Drop-in Replacement: IS200TVBAH2 — The base revision. Direct hardware match. The ‘AAA’ is a significant upgrade in signal quality.

⚠️ Software Compatible: IS200TVBAH1AAA — Lower-density H1 variant. Fits the same slot but has fewer vibration channels. Requires software reconfiguration. Budget 4-6 hours.

⚠️ Software Compatible: IS200TBCI1A — General-purpose analog I/O board. Requires external vibration signal conditioning and complete rework. Budget 8-12 hours.

❌ Hardware Incompatible: IS200TBQGH1A — Excitation termination board. Different pinout and application.

Frequently Asked Questions (FAQ)

Q: What types of vibration sensors does the TVBA board support?

A: The TVBA supports accelerometers and proximity probes (eddy current probes) commonly used for turbine shaft and bearing vibration monitoring. The board provides the necessary signal conditioning for both sensor types.

Q: What’s the difference between the H1 and H2 variants?

A: The H2 variant has higher channel density—more vibration input channels per board than the H1. This saves rack space in applications with extensive vibration monitoring requirements.

Q: What improvements does the ‘AAA’ revision have over the ‘A’?

A: The ‘AAA’ has improved signal conditioning for better signal-to-noise ratio—about 15% better noise rejection on the vibration channels—and enhanced connector contacts for better long-term reliability.

Q: Can I replace a TVBAH2A board with a TVBAH2AAA without any changes?

A: Yes. The ‘AAA’ is a drop-in replacement. No software changes, no wiring changes, no configuration changes.

Q: Is the TVBA board hot-swappable?

A: We advise against hot-swapping vibration input boards. Interrupting vibration signals while the turbine is running could cause protection logic issues. Power down the cabinet segment before swapping.

Q: What bench testing should I do before installing a TVBA board?

A: Standard vibration input protocol. First, visual inspection. Second, verify continuity. Third, apply power and verify the board’s response using a vibration simulator or function generator. Fourth, verify signal conditioning settings. Fifth, run a 24-hour stability test at 50°C ambient.

Q: How do I verify I’m getting a genuine TVBA board?

A: Check component markings against GE documentation. Weigh the board; should be about 380 grams. Look for the GE holographic security label.

Q: Where do I find the official wiring diagram for the TVBAH2AAA?

A: GE document GEK-130555 covers the TVBA series. The H2 variant is detailed in the section specific to that configuration. Pay special attention to the sensor wiring requirements—accelerometers and proximity probes have different wiring schemes. Always cross-reference against your cabinet’s as-built drawings. Verify every channel before terminating.

A-B 9701-VWSB250AENM PLC
NI PXIE-6368 PLC
ABB 3HAC17484-9/02
GE 531305NTBANG1 PLC