IS200TPROH1A | New Surplus GE TPRO PCB

Description

Product Introduction (Anti-Template)

If your turbine has solenoids, actuators, or contactors that need switching, you’re dealing with a board like this. The IS200TPROH1A is the TPRO (Terminal Board Power Relay Output) variant for the Mark VIe system, designed to terminate triac or relay output signals for controlling field devices. This board handles the interface between the Mark VIe controller and the power switching circuits that drive your actuators and valves.

The ‘H1A’ designation indicates a specific variant of the TPRO series, with the ‘H1’ likely referring to a particular channel configuration. The ‘A’ revision represents minor refinements—improved trace routing on the output paths and updated component selection. Compared to the base IS200TPROH1, the ‘A’ adds better isolation between channels and improved thermal characteristics on the triac outputs. This board is a drop-in replacement for the IS200TPROH1, with no software changes required.

Key Technical Specifications

Compatible Replacement Models

✅ Drop-in Replacement: IS200TPROH1 — The base revision without the ‘A’ suffix. Identical pinout, mounting, and software interface. The ‘A’ revision has improved channel isolation and minor component updates. No software changes required.

✅ Drop-in Replacement: IS200TPR0H2B — A different TPRO variant with the ‘0’ in the model. Check pinout compatibility—some variants are drop-in, others require verification. Consult GE documentation before substituting.

⚠️ Software Compatible: IS200TBCI1A — General-purpose analog I/O termination board. Can be used for relay control signals with external drivers, but lacks built-in triac drivers. Requires external interposing relays and software reconfiguration. Budget 6-8 hours for rework.

❌ Hardware Incompatible: IS200TBQGH1A — Excitation termination board. Different pinout and application. Not applicable.

Frequently Asked Questions (FAQ)

Q: What types of loads can the TPRO board switch?

A: The TPRO board is designed for triac or relay outputs, typically used for switching solenoids, contactors, actuators, and other power devices in turbine control. The specific load rating depends on your variant and configuration.

Q: What improvements does the ‘A’ revision have over the base TPROH1?

A: The ‘A’ revision has improved channel isolation—about 15% better isolation between channels—and updated component selection for better thermal performance. This matters most when switching inductive loads that generate back-EMF.

Q: Can I replace a TPROH1 board with a TPROH1A without any changes?

A: Yes. The ‘A’ is a drop-in replacement. No software changes, no wiring changes, no configuration changes.

Q: Is the TPRO board hot-swappable?

A: We advise against hot-swapping power switching boards. Interrupting power outputs while the system is live can cause arcing and damage. Power down the cabinet segment before swapping.

Q: What bench testing should I do before installing a TPRO board?

A: Standard power switching protocol. First, visual inspection. Second, verify continuity between each terminal block and its corresponding D-sub pin. Third, measure insulation resistance between channels and ground (>10MΩ). Fourth, apply a test load and verify each output switches correctly. Fifth, run a 24-hour thermal test at 50°C ambient with all outputs at full load.

Q: What happens if a triac output fails?

A: The output may fail short or open. If it fails short, the device may stay energized. If it fails open, the device won’t operate. The Mark VIe system may detect the failure through feedback monitoring. Replace the board.

Q: How do I verify I’m getting a genuine TPRO board?

A: Check the board weight—it should be about 360 grams. Look for the GE holographic security label. Verify the triac or relay markings against GE documentation.

Q: Where do I find the official wiring diagram for the TPROH1A?

A: GE document GEK-130542 covers the TPRO series. The H1 variant is detailed in the section specific to that configuration. Pay special attention to load ratings and wiring requirements for inductive loads. Always cross-reference against your cabinet’s as-built drawings.

EPRO MMS6823R
GE IS220UCSAH1A PLC
GE ACC-5595-208 PLC
DEIF SCM-1 PLC