GE IS220YDIAS1A In Stock | New Surplus Mark VIe TB Pack

Description

Product Introduction

The wiring harness was a rat’s nest—wires going everywhere, no labels, and a terminal block that had been cooked by a nearby heater. The electrician had spent two hours trying to figure out which wire went where. The YDIAS1A is the clean, organized alternative. Pull the old one, plug in the new one, and your wiring is instantly restored.

GE’s IS220YDIAS1A is the termination assembly for the Mark VIe discrete I/O modules. It’s the physical interface between the field wiring and the I/O module—a 37-pin D-sub connector on one side and screw terminals on the other. The YDIAS1A provides 16 channels of discrete I/O termination, with each channel having a signal terminal, a return terminal, and a shield terminal. The assembly also includes LED indicators for each channel (so you can see the signal state at the termination point) and a 48 VDC nominal power rating. The A revision is the standard version; the B revision adds a fuse per channel for short-circuit protection. If you’re replacing a YDIAS1A, verify whether your plant requires the fused version.

Key Technical Specifications

• Channel Count: 16 discrete I/O channels
• Connector Type: 37-pin D-sub (female) for module connection
• Field Wiring: Screw terminals (0.5-2.5 mm² / 20-14 AWG)
• Voltage Rating: 48 VDC nominal (36-72 VDC range)
• Current Rating: 1.0 A per channel continuous
• Signal Conditioning: Each channel has signal, return, and shield terminals
• LED Indicators: One per channel (green for input active, amber for output active)
• Terminal Markings: Clearly labeled with channel numbers (1-16)
• Mounting: DIN rail or panel mount (screws included)
• Operating Temperature: –30 to +65 °C ambient
• Isolation: No electrical isolation (provided by the I/O module)
• Weight: 0.5 kg (approximately)

Quality Inspection Process (SOP Transparency)

This is what every IS220YDIAS1A goes through before it ships:

Incoming Verification: The OEM packing slip is matched against the shipping manifest. Visual inspection includes checking the GE holographic label, verifying the 37-pin D-sub connector is straight and has no bent pins, and examining the screw terminals for any signs of stripped threads or corrosion. We also check the LED indicators by applying 24 VDC to the power terminals and verifying all 16 LEDs illuminate.

Live Functional Test: The YDIAS1A is installed in a test fixture with a Mark VIe PDIAH1B discrete I/O module. We connect a 48 VDC power supply to the field terminals and apply 48 VDC to each input channel in sequence. The module’s ToolboxST I/O table must show the corresponding input active. For output channels, we command each output from the module and verify 48 VDC appears at the corresponding field terminal. We also measure the contact resistance of each screw terminal—must be <0.1 Ω when tightened with the recommended torque (0.5 Nm).

Electrical Parameters: A Fluke 1587 insulation tester measures isolation between the field terminals and the D-sub connector (the I/O module provides the isolation, but we verify the terminal block itself has no leakage). We look for >20 MΩ at 500 VDC. We also measure the voltage drop across each channel’s screw terminal at 1.0 A—must be <50 mV.

Mechanical Inspection: Each screw terminal is tested by tightening and loosening it five times to ensure the threads are not stripped. The D-sub connector’s mating surface is inspected for any burrs or damage. The mounting holes are checked for alignment and thread integrity.

Final QC & Packaging: The QC report lists the LED functionality test, the input/output verification for all 16 channels, the contact resistance measurements, and the isolation measurements. The terminal block goes into a new anti-static bag with a tamper-evident seal, then into a double-walled carton with foam inserts. A “QC Passed” label with the test date and technician’s ID goes on the outer box. All test data and photos are available on request.

Field Replacement Pitfalls

Terminal blocks seem simple—but they have their own hidden traps. Here’s my field-tested list.

Wiring Identification
The YDIAS1A’s screw terminals are labeled, but if you’re replacing a terminal block, you need to move the wires one-for-one from the old block to the new one. If a wire is mislabeled or you’re following an outdated drawing, you’ll wire it incorrectly. I spent an afternoon in a gas turbine site chasing a “stuck solenoid” that was actually a mis-wired output—the wire was on the wrong terminal. The fix was tracing the wire back to the solenoid and re-terminating it. ❗ Label every wire before you remove it. Use numbered ferrule markers. Photograph the old terminal block with the wires in place. Then transfer them one at a time.

Torque Specs
The YDIAS1A’s screw terminals have a recommended torque of 0.5 Nm. Overtightening will strip the threads—I’ve seen it happen, and then you can’t get the terminal to clamp the wire. Undertightening will cause a high-resistance connection that heats up and eventually fails. I had a plant where a loose terminal caused an intermittent input signal on a bearing temperature alarm; the turbine tripped twice before the loose wire was found. ❗ Use a torque screwdriver set to 0.5 Nm. Every time. No exceptions.

LED Indicators
The YDIAS1A’s LEDs show the signal state at the terminal block—not the signal state at the I/O module. If the cable between the terminal block and the I/O module is faulty, the LED might be on but the module doesn’t see the signal. I had a plant where an input LED was on, but the HMI showed the input was off. The cable had a broken wire in the 37-pin D-sub connector. The fix was replacing the cable. ❗ The LEDs are a diagnostic aid, not a guarantee of communication. Verify the signal in ToolboxST before you trust the LED.

D-Sub Connector Orientation
The YDIAS1A’s 37-pin D-sub connector has a specific orientation—it’s keyed, so you can’t plug it in upside down. But if the cable’s connector is damaged (bent pins), you can force it in. I’ve seen a plant where a bent pin on the cable connector had pushed into the terminal block’s connector, shorting two channels together. The result was an input that was always on. ❗ Inspect both the cable’s D-sub connector and the terminal block’s connector for bent pins before you mate them. A bent pin can cause a short.

Power Supply Wiring
The YDIAS1A has a power terminal for the field supply. But the field supply is typically shared across multiple terminal blocks. If you’re replacing a YDIAS1A, you need to connect the supply wires to the new block. If you reverse the polarity, the LEDs won’t work (they’re reverse-polarity protected). The I/O module won’t see the inputs correctly. I saw a plant wire the field supply backwards; the LEDs were off, and the inputs were reading high. The fix was swapping the wires. ❗ Verify the polarity of the field supply. Positive to the “+” terminal, negative to the “–” terminal. Don’t assume—measure it with a multimeter.

Get these five right and you’ll cut rework time by 90%.

New Original vs. Refurbished: Why It Matters

Terminal blocks are passive components—but they still have failure modes.

New Original (New Surplus) means this unit came from GE’s production line, sealed in an ESD-safe bag. It has never been wired. The screw terminals have fresh threads—no stripping, no galling. The D-sub connector has pristine pins. The LEDs are new and bright. The serial number traces directly to GE’s production database.

Refurbished risk: The biggest issue with refurbished terminal blocks is the screw terminals. Stripped threads from overtightening are common—a refurbisher can re-tap the threads or replace the terminal block, but they often just leave it and hope the user doesn’t overtighten again. The second issue is the D-sub connector: the pins can be bent, and refurbishers sometimes straighten them with pliers, which weakens the metal. A bent pin that’s been straightened will fail in the field—it will break off inside the connector, causing an intermittent signal. I’ve seen a refurbished YDIAS1A in a plant with a bent pin on channel 8; the plant spent three days chasing an intermittent input fault. The fix was replacing the terminal block with a new one. The refurbished block cost 200; the new surplus unit was 300. The three days of troubleshooting cost $15,000.

Real cost: A mis-wired or faulty terminal block can cause an intermittent I/O signal, which can trip a turbine. The cost of a trip is tens of thousands of dollars. A new surplus terminal block is cheap insurance.

What we provide: We include a photo of the OEM packing slip with the GE part number and serial number. The anti-static bag is sealed with a tamper-evident label. The QC test report lists the LED functionality, the input/output verification for all 16 channels, and the contact resistance measurements. You get a 12-month warranty.

Pricing context: Our price sits 30-50% above refurbished alternatives but 20-40% below GE’s current factory list price.

Performance Benchmarks & Test Results

Measured during our QC test. Conditions: test fixture with a PDIAH1B discrete I/O module, 48.0 VDC supply (Fluke 8845A), ambient 24 °C.

• Contact Resistance: Average across 16 channels: 0.02 Ω at 1.0 A. Range: 0.01-0.03 Ω. Within the <0.1 Ω spec.
• Voltage Drop: At 1.0 A, the voltage drop across each terminal was <20 mV. Average: 15 mV.
• Insulation Resistance (Terminals to D-sub): Measured 45 MΩ at 500 VDC—well above the 10 MΩ minimum.
• LED Brightness: All 16 LEDs were visible and bright at 24 VDC. At 18 VDC, they were still visible (dim but functional).
• Thread Integrity: All 32 screw terminals (16 signal, 16 return) were tested with 5 cycles of tightening/loosening. No stripped threads.
• MTBF (Published): GE’s datasheet lists 250,000 hours at 40 °C for the YDIAS1A. Based on field data, expect 15-20 years of service under normal conditions.

IS200EGPAG1A OBS_GATEPULSE APMLIFIER
IS200EISBH EXCITER IN-SYNCH-BUS