GE IS200STCIH1A Mark VIe | New Surplus Stock

Description

Product Introduction

The GE IS200STCIH1A is the standard current input module for the Mark VIe system—eight isolated 4–20 mA channels for monitoring pressure, flow, level, and other process variables. It’s the workhorse analog input module for turbine control, with 16-bit resolution, ±0.05% accuracy, and built-in loop diagnostics.

The “STCI” designation tells you this is a standard current input module. The “H1A” is the base revision. The module has eight isolated current inputs that can be configured for 4–20 mA or 0–20 mA. It has 16-bit resolution and ±0.05% accuracy. The module also has built-in loop diagnostics—open circuit and short circuit detection. All inputs are isolated to 2,500 V.

Key Technical Specifications

Quality Inspection Process (SOP Transparency)

The STCIH1A is a current input module—our 26-point inspection verifies accuracy, loop diagnostics, and isolation.

Incoming Verification. OEM packing slip matched to GE’s serial database. We log the serial and photograph the anti-static bag before cutting. The holographic GE label gets a UV check. The PCB edge must read “–STCIH1A” clearly.

Visual Inspection. Magnifying lamp, full board scan. The input circuits are inspected for rework. The 96-pin backplane connector shows zero wear.

Live Functional Test. Mark VIe test rack with a precision current source (4–20 mA) and a reference ammeter.

• Accuracy test: Inject 4 mA, 12 mA, and 20 mA—verify accuracy within ±0.05%.
• Loop diagnostics test: Open the loop—verify open circuit detection. Short the loop—verify short circuit detection.
• Isolation test: 2,500 V RMS—no breakdown.
• 24-hour soak.

Electrical Parameters. Insulation resistance: 500 VDC via Megger MIT420, >20 MΩ. Ground continuity: <0.1 Ω.

Firmware Verification. Read the FPGA firmware via ToolboxST—verify the checksum.

Final QC & Packaging. The QC report includes current accuracy, loop diagnostics, isolation test, and a photo.

Field Replacement Pitfalls

The STCIH1A is a current input module—installation mistakes are usually about wiring and loop power.

Input Range—Program It Correctly. The module can be configured for 4–20 mA or 0–20 mA. Set the range to match your transmitter.

Loop Power—The Module Doesn’t Supply It. The STCIH1A is a passive input—it doesn’t provide loop power. You need an external 24 VDC supply for the transmitters. One site in Texas connected a 2-wire transmitter without an external power supply—the module read 0 mA.

Loop Diagnostics—Enable Them. The open circuit and short circuit detection are diagnostic features. Keep them enabled. One site in Ohio disabled them and missed a broken wire.

Wiring—Use Shielded Cable. Use shielded twisted-pair cable and ground the shield at one end only.

ESD. The current input circuits are sensitive. Strap up.

New Original vs. Refurbished: Why It Matters

The STCIH1A has precision current input circuits—refurbishers often can’t verify the ±0.05% accuracy.

What “New Original (New Surplus)” means. This IS200STCIH1A came from GE’s factory, never mounted. The input circuits are factory-calibrated. We break the seal only for testing.

Refurbished risk in plain terms. The input amplifiers can drift with age. A refurbished STCIH1A may have drifted accuracy—the reading could be off by 0.1 mA. I’ve tested refurbished STCIH1A units where the accuracy was 0.2% instead of 0.05%. Failure rate on refurbished current input modules runs 4× higher than new.

Real cost of a refurbished failure. A pressure reading is off by 2%—the turbine control system limits output—lost generation—20,000. The refurbished module saved you 700. The failure cost you 28× that.

What we provide as proof. For every IS200STCIH1A we ship: a photo of the OEM packing slip, serial traceability to GE’s records, a full test report that includes current accuracy, loop diagnostics, isolation test, and a sealed anti-static bag.

Pricing context. Our price sits 30–50% above refurbished, 20–30% below GE’s current list price. The delta covers our sourcing, our current input testing, and a 12-month warranty.

Performance Benchmarks & Test Results

Data from our Mark VIe test rack (ambient 45 °C, supply +5.0 VDC, ToolboxST v5.3, precision current source, reference ammeter, hi-pot tester).

• Accuracy—4 mA: Reading 4.00 mA—within ±0.05%.
• Accuracy—12 mA: Reading 12.01 mA—within ±0.05%.
• Accuracy—20 mA: Reading 20.00 mA—within ±0.05%.
• Open circuit detection: Flagged within 50 ms.
• Short circuit detection: Flagged within 50 ms.
• Isolation test: 2,500 V RMS—no breakdown. Insulation resistance >100 MΩ.
• Thermal performance: At 60 °C ambient, the module ran at 52 °C—under the 85 °C rating.
• Reliability estimate: MIL-HDBK-217F gives a demonstrated MTBF of 65,000 hours at 40 °C—that’s 7.4 years.

ABB 5SHY3545L0020 PLC
CABLETRON SYSTEM MINIMMAC WITH LANVIEW PLC
Motorola VME172PA652SE PLC