GE 531X307LTBAKG1 Control PCB | OEM New In Box

Description

Product Introduction

This GE 531X307LTBAKG1 is the ultimate logic and timing controller in the 307 series. The “K” suffix combines differential high-speed counter inputs, fiber-optic networking for harsh environments, and expanded memory for complex timing sequences—all on a single board. This is the highest-capacity, most hardened timing controller available for the DC-300 and AC-300 platforms.

The board provides 16 digital I/O points, 8 high-speed counter/timer channels with differential inputs (RS-422/TTL compatible, ±10 V common-mode rejection), dual fiber-optic ports (ST connectors) for GE proprietary deterministic networking, expanded memory (32 KB additional RAM, 64 KB additional EPROM), and a communications co-processor. This board is designed for the most demanding motion and timing applications in extreme industrial environments where standard communication and timing hardware would fail. It is the top-tier solution for applications requiring noise-immune timing, long-distance communication, and complex sequencing in a single module.

Key Technical Specifications

Key Selling Points & Differentiators

• Triple Feature Set: Fiber-Optic + Differential Counters + Expanded Memory: This board combines the three most critical features for harsh-environment timing applications. It is the only board in the 307 series that provides all three capabilities in a single module.
• Expanded Memory for Complex Sequences: 32 KB additional RAM and 64 KB additional EPROM support large timing tables, extensive data logs, and complex cam profiles. Standard boards are limited to smaller sequences.
• Complete Electrical Isolation: Fiber-optic networking eliminates ground loops. Differential counter inputs reject common-mode noise. All I/O is opto-isolated. This board is designed for the highest noise immunity.
• Quantified Testing Protocol: We test counter channels at 100 kHz with common-mode noise injection. Fiber-optic communication is tested with a 2 km equivalent optical attenuator. Memory is pattern-tested. The board runs for 12 hours under full timing, memory, and network load.
• Warranty & Support: 2-year functional warranty. We provide the most comprehensive documentation package in the 307 series, including fiber-optic installation, differential wiring, timing configuration, and memory utilization guides. We also include a fiber cleaning kit.

Frequently Asked Questions (FAQ)

Q1: What is the difference between the LTBAKG1 and the LTBAJG1?

A: The LTBAJG1 has standard memory (8 KB RAM, 16 KB EPROM) with fiber-optic ports and differential counter inputs. The LTBAKG1 has expanded memory (32 KB additional RAM, 64 KB additional EPROM) with the same fiber-optic and differential features. The expanded memory supports larger timing tables, more extensive data logging, and complex sequences. The hardware and I/O are identical. Choose the K variant for complex applications requiring large timing tables.

Q2: What can I do with the expanded memory that I cannot do with standard memory?

A: The expanded memory allows for up to 1,000 stored timing events instead of 100, larger data logs for process tracking, and support for complex cam tables and registration profiles with hundreds of points. It also allows for larger user-defined logic tables in custom firmware applications. If your application is simple—a few counters and a single PWM output—standard memory is sufficient. For multi-axis registration with dozens of timing events, the expanded memory is essential. The memory is managed by the co-processor and is not directly user-accessible.

Q3: Does this board support Modbus RTU or Ethernet?

A: No. The fiber-optic ports use GE’s proprietary deterministic network protocol (Genius or equivalent). The board does not support Modbus RTU, Modbus TCP, or Ethernet/IP. It has no RS-422/485 port and no Ethernet ports. It has only one RS-232 port for local programming. If you need Modbus or Ethernet, you need a different LTB variant or a network bridge. This board is strictly for GE drive-to-drive fiber-optic networks.

Q4: What signal types are compatible with the differential counter inputs?

A: The differential inputs accept RS-422 signals (typical ±5 V differential), TTL differential signals (0-5 V), and 24 VDC differential signals. The inputs are protected against overvoltage up to ±30 V. The common-mode rejection is ±10 V. Do not connect single-ended signals to the differential inputs—the negative input must be connected to the signal return. We provide a signal compatibility table in our documentation.

Q5: What is the maximum fiber-optic cable length for this board?

A: The standard transceivers support up to 2 km (1.2 miles) with 62.5/125 µm multimode fiber. The board uses ST connectors. Each drive regenerates the signal, so you can extend beyond 2 km with additional drives. We provide a fiber link budget calculator with the board. Do not use single-mode fiber or other connector types without an adapter.

Q6: Can the counter/timer channels be used as outputs for pulse generation?

A: Yes, the channels can be configured as PWM outputs or pulse train generators. The PWM output frequency can be set from 0.1 Hz to 100 kHz with 16-bit duty cycle resolution. This is useful for proportional valve control, heater control, or generating speed reference pulses. The PWM outputs are available on the digital I/O channels when configured for PWM mode. The expanded memory does not change the PWM capabilities—they are identical to the standard boards.

Q7: Does this board support quadrature encoder inputs?

A: No. The counter/timer channels are single-ended counting inputs—they count pulses on a single input line. They do not support quadrature (A/B) decoding or direction counting from quadrature signals. For quadrature encoder support, you need the MCPA series motion control boards. The LTBAKG1 is for simple pulse counting, frequency measurement, and timing tasks.

Q8: Can I use this board with an Allen-Bradley PLC over fiber-optic?

A: No. The fiber-optic network uses the GE proprietary protocol, which is not compatible with Allen-Bradley or other standard PLC networks. To connect this board to a non-GE PLC, you would need a network bridge module. The board itself is strictly for GE drive-to-drive networks. This is a common misunderstanding—verify your network architecture before ordering. The board does not support DF1, Modbus, or Ethernet/IP.

Q9: Is the LTBAKG1 still in production?

A: No, this board is discontinued and is the rarest board in the entire 307 series. GE produced the fiber-optic, differential, memory-expanded timing controller in extremely limited quantities for specialized high-EMI applications. We have a single very small batch of new surplus units. Used pulls are practically non-existent and often damaged. If your application requires this specific combination of features, we strongly recommend securing a spare. Our new surplus units are fully tested and guaranteed. We do not expect to source more of this variant.

Q10: Is this board a drop-in replacement for the LTBAFG1 or LTBAHG1?

A: Physically, yes—the same dimensions, mounting holes, and 50-pin ribbon connector. However, the terminal block wiring is different because of the fiber-optic ports and differential counter inputs. The LTBAFG1 and LTBAHG1 have serial ports (RS-232 and RS-422/485) instead of fiber-optic ports. The LTBAKG1 has fiber-optic ports and no RS-422/485 port. If you are upgrading from a serial-based LTB board, you must rewire your network connections for fiber-optic. The digital I/O and counter input wiring are the same as the differential variants (FG1, HG1, JG1). We provide a comprehensive transition guide for all upgrade paths.

SIEMENS 1FK6042-6AF71-1TH0
A-B 1747-L551
ABB AX670
BENTLY 3500/92-04-01-02