DS200TCTSG2ACC | 32-Ch Thermocouple Board

Description

Product Introduction (Anti-Template)

The DS200TCTSG2ACC is the most advanced ultra-high-density shared-CJC thermocouple input board GE produced for the Mark VI system—the board that combines 32 thermocouple inputs in one VME slot with shared CJC, reinforced isolation (1800Vrms), extended temperature operation (-20°C to +70°C), enhanced EMC protection (10V/m radiated immunity), diagnostic LEDs per channel, and advanced time-stamping (±100µs accuracy). If you need many thermocouple inputs in a harsh environment with shared CJC and precise event correlation, this board is the ultimate solution.

The ‘TCTS’ in the part number indicates this is a thermocouple input board with shared CJC. The ‘2’ indicates the ultra-high-density variant (32 channels). The ‘ACC’ suffix tells you this is the enhanced version: reinforced isolation (1800Vrms), extended temperature range (-20°C to +70°C), enhanced EMC protection, 14-bit resolution, ±0.6°C accuracy, shared CJC, diagnostic LEDs per channel, and advanced time-stamping with ±100µs accuracy. Compared to the TCTSG2A (standard isolation, 0-55°C, no time-stamping), the ‘ACC’ gives you reinforced isolation, extended temperature range, and advanced time-stamping. If you need to monitor many thermocouples in a harsh environment with shared CJC and precise event correlation, this board is the solution.

Key Technical Specifications

Compatible Replacement Models

Replacement options depend on your need for reinforced isolation, extended temperature, and advanced time-stamping.

✅ Drop-in Replacement: The DS200TCTSG2A (no ‘CC’) is a direct electrical drop-in—same pinout, same 32 inputs, same shared CJC, same update rate. The differences: the ‘A’ has standard isolation (1500Vrms), standard temperature range (0-55°C), standard EMC, and no time-stamping. If your environment is benign and your requirements are standard, the ‘A’ is a cheaper option (typically 25-35% less). The ‘ACC’ is for harsh environments requiring reinforced isolation and time-stamping.

⚠️ Software Compatible: The DS200TCTEG1A (16 inputs, per-channel CJC, 16-bit, ±0.4°C accuracy) provides better accuracy and per-channel CJC with half the channels. Only use if you need better accuracy.

⚠️ Software Compatible: The DS200TCTGG2A (32 inputs, per-channel CJC, 15-bit, ±0.5°C accuracy) provides better accuracy with per-channel CJC. Only use if you need better accuracy.

❌ Hardware Incompatible: Any general-purpose analog input board (TCCAG1 series) uses different backplane pins and is not suitable for thermocouple signals.

Frequently Asked Questions (FAQ)

What does the ‘ACC’ suffix mean on this ultra-high-density shared-CJC thermocouple board?

GE’s suffix coding for the TCTSG2ACC: the ‘A’ is the base platform (thermocouple input, 32 channels, shared CJC, 14-bit). The ‘C’ indicates reinforced isolation (1800Vrms), extended temperature range (-20°C to +70°C), and enhanced EMC protection. The final ‘C’ is the production revision with advanced time-stamping (±100µs), improved accuracy (±0.6°C), and enhanced diagnostics. So ‘ACC’ is the most robust, time-stamping-enabled version of the TCTSG2 platform.

What’s the difference between shared CJC and per-channel CJC?

Shared CJC (TCTSG2ACC) uses a single CJC sensor for all 32 thermocouple inputs. This assumes the termination board is isothermal (same temperature across all terminals). Per-channel CJC (TCTGG2A) uses individual CJC sensors per channel, eliminating the error from temperature gradients. Shared CJC is cheaper but less accurate—if there’s a temperature gradient, the error can be 1-2°C. The reinforced isolation helps reduce noise but doesn’t correct CJC gradients.

Why doesn’t this board support R, S, or B thermocouples?

The TCTSG2ACC uses a 14-bit ADC that doesn’t have the dynamic range to accurately measure R, S, and B thermocouples. The board is designed for general-purpose temperature monitoring (J, K, T, E, N).

Can I use this board with a Mark VIe controller?

No—the TCTSG2ACC uses the older Mark VI backplane pinout. Mark VIe uses a different assignment and typically uses the IS200TCTSG2ACC for thermocouple inputs. Use the Mark VIe-specific board for new installations.

How do I test this board before installation?

Testing the TCTSG2ACC requires checking all 32 channels, verifying reinforced isolation, EMC protection, enhanced diagnostics, and timestamp accuracy:

1. Visual inspection: Check for burnt components. Look for diagnostic LEDs, larger isolation transformers, and the time-stamping circuit.
2. Power-up test: Apply power. All diagnostic LEDs should cycle through their patterns during POST.
3. Firmware check: Read firmware via ToolboxST—should be 4.0 or later.
4. CJC test: With no thermocouple connected, read the CJC temperature—should match ambient within ±0.15°C.
5. Input test: Apply 10.00mV to input 1—read 250°C ± 0.6°C. Repeat for inputs 1-32.
6. Diagnostic LED test: Disconnect a thermocouple—LED should flash amber or red.
7. Time-stamping test: Apply a known event to an input and record the timestamp. Verify accuracy within ±100µs.
8. EMC test (if equipment available): Apply a 10V/m radiated RF field—verify inputs remain stable.
9. Isolation test: Apply 1800Vrms between an input channel and ground for 1 minute.
10. Temperature test: Cycle from -20°C to +70°C—verify operation.

What’s the most common failure on this board?

1. CJC sensor drift. The single shared CJC sensor can drift over time—symptom: a consistent offset on all channels.
2. Multiplexer failure. The TCTSG2ACC uses a multiplexer to handle 32 channels—if it fails, you’ll get erratic readings on specific channels.
3. Time-stamping circuit failure. Timestamp data becomes inaccurate or unavailable.

If I’m using this board in a SIL-rated safety application, what’s the recommended maintenance interval?

The shared CJC design makes this board suitable for SIL-1 applications (not SIL-2 or SIL-3). We recommend:

• Visual inspection: Every 6 months (check diagnostic LEDs)
• Power-up test: Every 12 months
• CJC test: Every 12 months
• Input accuracy check: Every 12 months (0.6°C spec)
• Time-stamping test: Every 12 months (±100µs spec)
• EMC test (if equipment available): Every 5 years
• Isolation check: Every 2 years
• Full calibration: Every 5 years

What’s the lead time for a replacement TCTSG2ACC?

These are the rarest and most advanced ultra-high-density shared-CJC thermocouple boards:

• New surplus: 4-8 weeks. The ‘ACC’ commands a premium—expect 35-45% above the TCTSG2A.
• Refurbished: 2-4 weeks. Requires specialized calibration equipment and timestamp verification.
• Used/as-is: Extremely high risk—used boards are almost never in spec.

Is there a direct Mark VIe equivalent?

Yes—the IS200TCTSG2ACC (Mark VIe version). The backplane pinout is different.

What termination board should I use with the TCTSG2ACC?

The TCTSG2ACC is designed to interface with the DS200TBCSG2 (high-density thermocouple termination board with shared CJC). The termination board provides the CJC sensor and the terminal connections. The reinforced isolation on the ‘ACC’ version provides better noise immunity for long cable runs. The shared CJC design assumes the termination board is isothermal—keep the termination board away from heat sources.

What’s the update rate for this board?

The TCTSG2ACC samples all 32 channels simultaneously at 20ms intervals—50Hz update rate. The timestamp is captured at the exact moment of sampling.

What’s the maximum cable length for thermocouples on this board?

GE recommends a maximum of 200 feet (60 meters) for thermocouple cable runs—shorter than the 16-channel boards (250-300 feet) due to the higher channel density and lower input impedance. The reinforced isolation on the ‘ACC’ version provides better noise immunity for long cable runs. The shared CJC design assumes the termination board is isothermal—keep the termination board away from heat sources.

MVME162-743 PLC DCS
CI626K1 3BSE012868R1 PLC DCS
DO630 3BHT300007R1