Bently Nevada 125840-01 | 3500/15 AC Power Supply, New Surplus

  • Model: 125840-01
  • Brand: Bently Nevada (Baker Hughes)
  • Series: 3500 Machinery Protection System — 3500/15 power family
  • Core Function: Takes high-voltage AC site power and delivers regulated DC rails to every slot in a 3500 rack.
  • Type: AC Power Input Module (half-height)
  • Key Specs: High-voltage AC input variant; half-height supply card; pairs with a second module for redundancy
  • Condition: New Original (New Surplus) — not refurbished
Manufacturer:

Our extensive catalogue, including , is available now for dispatch to the worldwide.
  • Email: jiedong@sxrszdh.com
  • Phone / Wechat:+86 15340683922

Description

 

Product Introduction

Wrong input variant is the fastest way to kill a fresh power card. The BENTLY 125840-01 is the high-voltage AC input member of the 3500/15 power supply family, and it feeds the regulated rails that keep every monitor, relay, and comms card in a 3500 rack alive. Order the low-voltage variant for a high-voltage feed and you’ll hear the breaker trip before you finish tightening the terminal screws.

Half-height form factor, dedicated supply slots, and redundant pairing through the backplane. That last part deserves attention — a single supply on a turbine train is a calculated risk, and the plants that run paired modules sleep better. Confirm your rack’s incoming voltage and the label on the card before you order. They must match.

 

Key Technical Specifications

Parameter Value
Part Number 125840-01
Module type AC power input (half-height)
Platform Bently Nevada 3500 rack
Input High-voltage AC per unit label — confirm before order
Output Regulated DC rails to 3500 backplane
Redundancy Supports paired supply in dedicated slots
Slot requirement Dedicated power supply slot
Front-panel indicators Power and fault LEDs
Operating temperature 0 to +65 °C (rack ambient)
Storage temperature −40 to +85 °C
Mounting 3500 backplane connector
Fusing Verify rating against OEM datasheet

 

Quality Inspection Process

Power cards get the hardest look on our bench. A supply that sags under load produces intermittent faults that frame every other module in the rack.

Incoming verification. OEM packing slip or customs documents matched to the serial number before the box opens. Bently Nevada serial lookup, hologram check where present. Visual inspection begins with the electrolytic capacitors — bulging, leaking, or vented means instant reject. Then connector pins for corrosion, board for reflow marks, transformer and heatsink for heat discoloration. Mounting hardware counted against the packing list.

Live functional test. Module installed in a working 3500 rack with known-good monitor cards. Output rails measured at the backplane with a Fluke 115 multimeter at no-load, half-load, and full-load. Ripple checked on a scope. Redundant-pair load sharing and single-module failover verified where a second supply is available. A 24-hour continuous run follows with rail voltages logged every 15 minutes.

Electrical parameters. Insulation resistance at 500 V megger, >10 MΩ required. Ground continuity from chassis to backplane. Input fusing checked against OEM rating.

Firmware verification. Not applicable — hardwired supply. Backplane revision and jumper positions photographed instead.

Final QC and packaging. QC sign-off with test data sheet, anti-static bag, bubble wrap, rigid carton, QC Passed label with date. Test photos and video available on request.

 

Field Replacement Pitfalls

Input voltage mismatch, first and always. The 125840-01 is the high-voltage AC variant, and its sibling cards in the 3500/15 family take different feeds. Read the label, match it to the rack supply, confirm against the OEM datasheet. A mismatched card either trips the upstream breaker or sits dead with a green LED and no output.

Redundant pairing needs matching variants. ❗ Two supplies in a redundant pair must be the same variant and see the same input source. I’ve seen a pair split between a UPS feed and raw mains — failover tested fine, then a brownout on the raw side sagged the shared rail and dropped half the rack. Wire per the OEM diagram and verify load sharing before you trust it.

Photograph the old module’s slot position before removal. Backplane revisions change connector keying. A card forced into the wrong slot bends pins that cost more than the module.

Capacitor aging is the silent failure. Ten years on an original supply is a long service life. When you replace one side of a redundant pair, replace both — a fresh card and a tired one share load unevenly, and the old one dies first.

ESD. Wrist strap. Bulk capacitors and the regulator stage do not tolerate static discharge.

Get these five right and the rack comes back clean.

 

New Original vs. Refurbished: Why It Matters

New Original (New Surplus) means OEM-manufactured, original packaging opened only for our bench test, fresh capacitors with full service life ahead, no connector wear, no board-level repairs, and a serial number that traces to Bently Nevada.

Refurbished supplies carry a specific gamble. Capacitors age first in any power module, and a refurbished unit’s caps may already be years into their life under a cleaned exterior. Failure rates run 3–5× higher than new stock. Without a traceable serial, OEM support and replacement programs stop at the door.

One unplanned trip on a protected machine can cost 10× the price gap. What we provide: OEM packing slip photo, traceable serial number, bench test data sheet with rail voltages and ripple, anti-static bag seal or documented reason for opening. Price sits 30–50% above refurbished and 20–40% below OEM list — the delta covers global sourcing, the QC routine above, and a 12-month warranty.

 

Performance Benchmarks & Test Results

Bench data from our 3500 test rack, 25 °C ambient, input at nominal AC site voltage, output into a loaded rack:

  • Output rails: within OEM tolerance at no-load, half-load, and full-load — per-unit values recorded on the test sheet
  • Ripple: measured on scope, within OEM spec
  • Redundant pair: load sharing verified; single-module failover held the rack online
  • 24-hour continuous run: rail voltages stable, ambient 22–27 °C, no dropouts
  • Insulation resistance: >10 MΩ at 500 V megger
  • Thermal note: rack ambient above 55 °C changes supply derating — check the OEM curve before deploying in an unventilated cabinet

Exact input range, output current limit, and MTBF figures vary by revision — verify against the OEM datasheet for your specific unit.

 

FAQ

What input voltage does the 125840-01 accept?
It’s a high-voltage AC input variant. Confirm the exact range on the unit label and against the OEM datasheet before connecting site power.

Can I pair the 125840-01 with another 3500/15 supply for redundancy?
Yes, provided both modules are the same variant and share the same input source. Verify against the OEM wiring diagram.

Is this power module new or refurbished?
New Original (New Surplus) — OEM-manufactured, bench-tested with fresh capacitors, traceable serial number. Not refurbished.

How do I know my 3500 power supply is failing?
Random module dropouts, fault LEDs, drifting rails under load. Measure at the backplane before blaming monitor cards.

SCHNEIDER ATV31HU40N4A
SCHNEIDER ATV320D15N4С
NAICH AUX111
杂牌 AUXL111A
ABB AV94A HESG440940R11

Brand new✔ In stock ✔ Fast shipping✔
  • Email: sales@plcfcs.com
  • Phone:+86 15343416922
  • Wechat:+86 15343416922
Advantageous products we supply
PLC : Allen Bradley , Siemens MOORE, GE FANUC , Schneider
DCS : ABB ,Honeywell, Invensys Triconex , Foxboro , Ovation,YOKOGAWA, Woodword, HIMA
TSI : Triconex , HIMA , Bently Nevada , ICS Triplex
Complete service we offer
Payment: T/T
Delivery: 1-2 days
Shipment: DHL UPS FedEx, etc
After-sales service: Yes, 24/7 hours