Bently Nevada 106M1081-01 | Replacement Power Input, 12-Mo Warranty

  • Model: 106M1081-01
  • Brand: Bently Nevada (Baker Hughes)
  • Series: 3500 Machinery Protection System
  • Core Function: Converts incoming AC or DC site power into regulated rails that feed every module in a 3500 rack.
  • Type: Power Input Module (PSU)
  • Key Specs: 3500 rack power supply slot; feeds monitor and relay modules; redundant-supply capable with a second module
  • Condition: New Original (New Surplus) — not refurbished
Manufacturer:

Our extensive catalogue, including , is available now for dispatch to the worldwide.
  • Email: jiedong@sxrszdh.com
  • Phone / Wechat:+86 15340683922

Description

Product Introduction

Every 3500 rack has one component that fails quietly and takes the whole protection system with it — the power input module. The Bently Nevada 106M1081-01 is the supply card that turns site power into the regulated rails feeding each monitor and relay slot, and when it drifts out of spec, modules start dropping offline one at a time and everybody blames the monitors.

The 3500 platform supports a second supply module for redundancy, and honestly, if your rack runs a critical turbine train, you should be using it. This card slots alongside a partner supply and shares the rail load. Single-supply racks are fine on a compressor skid with a spare panel — not so much on a machine that trips the plant. Confirm your rack voltage configuration and backplane revision before ordering.

 

Key Technical Specifications

Parameter Value
Module type Power input module
Platform Bently Nevada 3500 rack
Input voltage Site AC/DC per OEM configuration — confirm before order
Output Regulated rails feeding 3500 backplane
Redundancy Supports paired module for redundant supply
Slot requirement Dedicated power supply slot(s)
Front-panel indicators Power and fault LEDs
Operating temperature 0 to +65 °C (rack ambient)
Storage temperature −40 to +85 °C
Mounting 3500 backplane connector
Fusing Verify fuse rating against OEM datasheet
Firmware Not applicable — hardwired supply

 

Quality Inspection Process

Power modules get extra attention on our bench because a marginal supply creates intermittent faults that look like everything except a supply problem.

Incoming verification. OEM packing slip or customs docs matched to serial number. Bently Nevada serial lookup and hologram check where present. Visual inspection covers the electrolytic capacitors first — bulging or leaking caps mean instant reject. Then connector pins for corrosion, board for reflow marks, transformer for discoloration.

Live functional test. Module installed in a working 3500 rack with known-good monitor cards. Output rails measured at the backplane with a Fluke 115 multimeter under no-load, half-load, and full-load conditions. Ripple measured on a scope. Redundant-pair operation tested if you’re buying two — we confirm load sharing and failover. 24-hour continuous run with rail voltages logged every 15 minutes.

Electrical parameters. Insulation resistance at 500 V megger, >10 MΩ. Ground continuity. Input fusing verified against OEM rating.

Firmware verification. Not applicable to this module — it’s a hardwired supply. Backplane revision and jumper positions photographed instead.

Final QC and packaging. QC sign-off with test data sheet, anti-static bag, bubble wrap, carton. Test photos and video available on request.

 

Field Replacement Pitfalls

Input voltage mismatch is the first thing to check. The 106M1081-01 comes in configurations for different site voltages, and pulling a card rated for the wrong input will either trip the upstream breaker or sit dead. Read the label, match it to your rack feed, and confirm against the OEM datasheet before you power up.

Redundant supply wiring, if you run it. Both modules must see the same input source and share the rail correctly. ❗ I’ve seen a “redundant” pair wired to two different feeds — one on the UPS, one on raw mains — and the failover test passed, but a brownout on the raw side sagged the shared rail and dropped half the rack. Confirm load-sharing behavior with the OEM diagram.

Photograph the old module’s slot position and any jumper settings before removal. Backplane revisions change connector keying, and a card forced into the wrong slot bends pins.

Capacitor aging is the quiet failure mode on any supply. If the rack has been running for 10+ years on the original supply, replace both modules if you run redundancy — a fresh card paired with a tired one shares load unevenly.

ESD. Wrist strap on, every time. The supply board carries the bulk capacitors and the regulator stage — both dislike static.

Get these right and the rack comes back clean.

 

New Original vs. Refurbished: Why It Matters

New Original (New Surplus) means OEM-manufactured, original packaging opened only for our bench test, fresh electrolytic capacitors with full service life ahead, no connector wear, no board-level repairs, and a serial number that traces to Bently Nevada.

Refurbished supplies are a specific gamble. Capacitors are the first thing to age in any power module, and a refurbished unit’s caps may already be years into their life under a cleaned-up exterior. Failure rates run 3–5× higher than new stock. Without a traceable serial, OEM support and replacement programs stop at the door.

One unplanned trip on a protected machine can cost 10× the price gap. What we provide: OEM packing slip photo, traceable serial number, bench test data sheet with rail voltages and ripple, anti-static bag seal or documented reason for opening. Price sits 30–50% above refurbished and 20–40% below OEM list — the delta covers global sourcing, the QC routine above, and a 12-month warranty.

 

Performance Benchmarks & Test Results

Bench data from our 3500 test rack, 25 °C ambient, input at nominal site voltage, output into a loaded rack:

  • Output rails: measured within OEM tolerance at no-load, half-load, and full-load — values recorded on the test sheet per unit
  • Ripple: measured on scope, within OEM spec
  • Redundant pair: load sharing verified; single-module failover held the rack online
  • 24-hour continuous run: rail voltages stable, ambient logged 22–27 °C, no dropouts
  • Insulation resistance: >10 MΩ at 500 V megger
  • Thermal note: rack ambient above 55 °C changes supply derating — check the OEM curve before deploying in an unventilated cabinet

Exact input ranges, output current limits, and MTBF figures vary by revision — verify against the OEM datasheet for your specific unit before quoting numbers.

 

FAQ

Can I run the 106M1081-01 as a single supply without a second module?
Yes, the 3500 rack runs on a single supply. Redundancy is optional but recommended for critical machine trains.

What input voltage does the 106M1081-01 accept?
Input configuration varies by unit. Read the label and confirm against the OEM datasheet before connecting site power.

Is this power module new or refurbished?
New Original (New Surplus) — OEM-manufactured, bench-tested with fresh capacitors, traceable serial number. Not refurbished.

How do I know when a 3500 power supply is failing?
Intermittent module dropouts, front-panel fault LEDs, and drifting rail voltages are the usual signs. Measure rails under load before condemning the supply.

 

Brand new✔ In stock ✔ Fast shipping✔
  • Email: sales@plcfcs.com
  • Phone:+86 15343416922
  • Wechat:+86 15343416922
Advantageous products we supply
PLC : Allen Bradley , Siemens MOORE, GE FANUC , Schneider
DCS : ABB ,Honeywell, Invensys Triconex , Foxboro , Ovation,YOKOGAWA, Woodword, HIMA
TSI : Triconex , HIMA , Bently Nevada , ICS Triplex
Complete service we offer
Payment: T/T
Delivery: 1-2 days
Shipment: DHL UPS FedEx, etc
After-sales service: Yes, 24/7 hours